Enhanced hydrogen desorption kinetics and cycle durability of amorphous TiMgVNi3-doped MgH2

MgH₂ is considered as a promising hydrogen storage material for on-board applications. In order to improve hydrogen storage properties of MgH₂, the amorphous TiMgVNi₃-doped MgH₂ is prepared by ball milling under hydrogen atmosphere. It is found that the catalytic (Ti,V)H₂ and Mg₂NiH₄ nanoparticles are in situ formed after activation. As a result, the amorphous TiMgVNi₃-doped MgH₂ exhibits enhanced dehydrogenation kinetics (the activation energy for hydrogen desorption is 94.4 kJ mol^?1 H₂) and superior cycle durability (the capacity retention rate is up to 92% after 50 cycles). These results demonstrate that the in situ formation of highly dispersed catalytic nanoparticles from an amorphous phase is an effective pathway to enhance hydrogen storage properties of MgH₂.     

Sea urchin-like LiAlO2@NiCoO2 hybrid composites with core-shell structure as high-performance Li storage materials

Sea urchin-like LiAlO₂@NiCoO₂ hybrid composites with core-shell structure assembled with nanoneedles have been successfully fabricated through a facile hydrothermal route followed by a calcination procedure in N₂ for the first time. The sea urchin-like architecture with large accessible surface can offer numerous active sites for redox reaction. The synergy of two advantages has dramatically improved the electrochemical behavior in terms of specific capacity, cycle performance and rate capability, especially at high current densities. The LiAlO₂(5.0 wt%)@NiCoO₂ displays charge capacities are 1309.0 and 933.6 mAh g^?1 at 0.5 and 1A g^?1, respectively, after 400 cycles. However, the charge capacities of bare NiCoO₂ are only 562.9 and 476.7 mAh g^?1 at corresponding rates. Especially, LiAlO₂(5.0 wt%)@NiCoO₂ preserves 358.1 mAh g^?1 after 500 cycles at 2A g^?1 with a capacity retention of 74%. The superior electrochemical property is related to the sea urchin-like nature and the ingenious composition design. In addition, the DFT calculation result shows that the formed stable, well-coordinated, and metallic interface between LiAlO₂ and NiCoO₂ are very helpful for reducing the interfacial impedance and beneficial for the improved rate capability of the materials. Therefore, such LiAlO₂@NiCoO₂ composites with unique morphology demonstrate a huge potential as electrode materials for Li-ion batteries.     

Microstructure,mechanical and tribological properties of Mo–V–Cu–N coatings prepared by HIPIMS technique

A combination of high wear-resistance and low-friction is crucial for improving the wear performance of self-lubricating coatings, which is generally determined by an excellent lubricating effect and mechanical strength. In this study, the Mo–V–Cu–N coatings were prepared by HIPIMS technique with a spliced target of Mo–V–Cu at various charge voltages. The results revealed that Mo–V–Cu–N coatings presented a solid solution phase of B1–MoVN with (200) preferred orientation, and the preferred orientation was enhanced at high charge voltages. Whereas the Cu atoms formed an amorphous phase in Mo–V–Cu–N coatings due to a low Cu content of 2.3–3.6 at.%. As the charge voltage increased to 750 V, more charged metallic ions were accelerated and bombarded substrate surface efficiently, forming smooth and dense Mo–V–Cu–N coatings with a high hardness of 31.0 GPa. All the coatings presented a low friction coefficient of 0.34–0.39 due to the formation of MoO₂, VO₂ and CuO mixed oxides, and the wear mechanism was dominated by abrasive and tribo-oxidation wear at room temperature.     

Iron doped thin TiO2 films synthesized with the RF PECVD method

Iron doped titanium dioxide coatings were synthesized with the help of RF plasma enhanced CVD technique. As a source of titanium, titanium chloride (IV) TiCl₄ was used while iron pentacarbonyl (0) Fe(CO)₅ served as iron supply. The coatings were diagnosed using Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Their elemental and chemical composition was studied with the help of X-ray energy dispersive spectroscopy (EDS) and Fourier transform infrared (FTIR) spectroscopy, respectively. For the determination of their optical properties, variable angle spectroscopic ellipsometry (VASE) and ultraviolet-visible (UV-Vis) spectroscopy techniques were used. Iron content in the range of 0.07–11.5 at% was found in the films. Apart from oxygen, titanium and iron, a presence of trace amounts of chlorine, very likely originating from the titanium precursor, was recorded. FTIR studies showed that iron was built-in in the structure of TiO₂ matrix. Surface roughness, assessed using SEM and AFM techniques, increases with an increasing content of this element. VASE measurements revealed an increase of the coatings refractive index with a growing iron concentration, with the extinction coefficient remaining low and independent of that parameter. Trace amounts of iron resulted in a lowering of an absorption threshold of the films as well as their optical gap, but the tendency was reversed for high concentrations of that element.     

Study of aging behavior of 9/70/30 and 9/65/35 PLZT by optical interferometric technique

In this work Pb_0.91La_0.09(Zr_0.70Ti_0.30)_0.9775O₃ PLZT (9/70/30) and Pb_0.91La_0.09(Zr_0.65Ti_0.35)_0.9775O₃ PLZT (9/65/35) ceramics were prepared at four different sintering temperatures by solid solution method. The samples were aged by keeping at room temperature for 19 days. After the aging process, structural and electrical properties of the samples were studied using Modified Michelson Interferometer, LCR meter and X-ray diffraction. The effect of the Zr/Ti ratios on the dielectric and ferroelectric properties was also investigated. The aged PLZT (9/70/30) showed pinched P–E loop and remnant strain in rhombohedral phase, while PLZT (9/65/35) showed distort s–E shape implying non-180° domain in tetragonal phase.     

Relationships between the accumulative damage and dielectric properties of woven BN-coated Hi-Nicalon™ SiC fibre-reinforced SiC matrix composites

The accumulative damage behaviour of BN-coated Hi-Nicalon™ SiC fibre-reinforced SiC matrix composite was examined under tensile cyclic loading at room and elevated temperatures. The accumulative damage occurring during the cyclic loading was quantitatively characterised using the damage parameter obtained by the hysteresis loop curves. The damage parameter increased with increasing applied stress beyond the matrix cracking stress, and it subsequently retained a nearly constant value until just before fracture. Moreover, the dielectric constant, dielectric loss and loss tangent of the composite were measured before and after the fracture in the frequency range 1–1000 MHz. The dielectric properties had similar frequency dependency before and after the fracture. However, the dielectric constant, dielectric loss and loss tangent were lower in the post-fractured specimens than in the pristine ones. The reduction of the dielectric properties was associated with the accumulative damage stored in the specimens. In addition, the relationships between the dielectric properties and the damage parameter were described in detail.     

Hydrothermal synthesis of 3D NixCo1−xS2 particles/graphene composite hydrogels for high performance supercapacitors

In this work, three dimensional (3D) Ni_xCo_1−xS₂/graphene composite hydrogels with different Ni contents (denoted as Ni_xCo_1−xS₂/GH (x = 0, 0.31, 0.56, 0.66, 1)) have been synthesized by a simple one-step hydrothermal method and utilized as the active materials of supercapacitors. The as-prepared samples present a 3D interconnected porous network with the pore sizes in the range of several to tens micrometers. Interestingly, the Ni_xCo_1−xS₂ particles are uniformly located on the graphene network and the particle size is evolved from ∼50 nm to ∼1.5 μm with the increase of Ni content. The electrochemical measurements revealed that the specific capacitance, rate capability and cyclability of different Ni_xCo_1−xS₂/GH electrodes are strongly affected by their different Ni content. Among these, the 3D Ni_0.31Co_0.69S₂/GH composite has the highest specific capacitance of 1166 F/g at a current density of 1 A/g. Furthermore, a specific capacitance of 559 F/g can be still maintained at high current density of 20 A/g. After 1000 charge–discharge cycles at 5 A/g, the specific capacitance remains a high value of 755 F/g.     

In2O3:Ga and In2O3:P-based one-electrode gas sensors: Comparative study

Gas sensing characteristics of one-electrode sensors based on the In₂O₃ ceramics doped by gallium and phosphorus have been discussed. In₂O₃-based ceramic was prepared by sol–gel technology. Ozone, CO, CH₄ and H₂ were used as tested gases. The doping concentration effect on the sensor parameters such as magnitude of response, operating temperature, response and recovery times, sensitivity to the air humidity, and selectivity have been analyzed. It was shown that In₂O₃ doping by Ga and P could be used for the sensor performance optimization. It was assumed that the appearance of the second phase (InPO₄ and Ga₂O₃) and the change of structural parameters, taking place during doping process, were the main factors controlling the change of operating characteristics in In₂O₃:P and In₂O₃:Ga-based sensors.     

Osteoinductive potential of biocomposite cylinders impregnated with Glycyrrhiza glabra for bone tissue engineering

Biocomposite cylinders containing biphasic calcium phosphate (BCP), collagen (CS), and an extract of Glycyrrhiza glabra (GG) were prepared and characterized for their physicochemical properties. Incorporation of BCP and GG enhanced the mechanical properties of the CS. The biomimetic mineralization capacity of CS–BCP–GG biocomposite cylinders was evaluated in a simulated body fluid solution. CS–BCP–GG biocomposite cylinders show over 80% viability in NIH-3T3 and SaOS-2 cell lines, compared to CS and CS–BCP. In vivo studies were performed using zebrafish embryos to find out the toxicity level of CS isolated from chrome shavings.     

High-pressure hydrogen storage performances of ZrFe2 based alloys with Mn,Ti, and V addition

The microstructure of ZrFe₂-based alloys were modified by alloying with the Mn, Ti, and V, aiming to obtain proper hydriding/dehydriding plateau features for the high-pressure application. The multi-component ZrFe₂-based alloys show a wide tunable range in the plateau pressure via the interaction of Ti, Mn, and V. Further, the V addition plays the best role to improve the hysteresis in absorption-desorption isotherms, while the proper addition amount Ti helps to realize a low plateau slope as well as a high plateau pressure. Among the investigated alloys, Zr_1.05Fe_1.6Mn_0.4 shows a relatively high dehydriding pressure of 20.58 atm at 298 K, while Zr_1.05Fe_1.7Mn_0.2V_0.1 with C15 structure shows the lowest hysteresis. Overall, too much of Ti and Mn would promote the transformation of the C15 to C14 structure with large hysteresis and low plateau pressure.